D External dimensions. D Connections. D Connection of motor. FANUC CONTROL MOTOR AMPLIFIER α series DESCRIPTIONS. B–E. B–E. FANUC AC SPINDLE MOTOR α series PARAMETER MANUAL B– E. FANUC SERVO AMPLIFIER α series DESCRIPTIONS. B–E. FANUC SERVO AMPLIF IER @ series DESCRIPTIONS BE/03 The export of this product is subject to the authorization of the.
|Published (Last):||3 October 2006|
|PDF File Size:||11.48 Mb|
|ePub File Size:||1.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
Fanuc B-65162 Manuals
However, we cannot describe all the matters which must not be done, or which cannot be done, because there are so many possibilities. Spindle Amplifier Module Connection Diagram. If a regenerative discharge unit with a resistance of 16? The ordering drawing numbers and specifications of the circuit breakers and magnetic contactors are shown below.
Motor rotation speed for rapid traverse [rpm] ta: Spindle switching control switching the speed only, or switching both the speed and position 2. Select a servo amplifier module according to the servo motor being used.
When transporting them or mounting them in the cabinet, therefore, be careful not to injured yourself or damage the equipment. NOTE 1 In the —V input series, the power supply is grounded by neutral grounding, so there is no leakage current that would cause a circuit breaker with a ground fault interrupter, connected on the power supply side, to malfunction.
In the event of an emergency stop, for example, the dynamic brake module stops the motor immediately by short—circuiting the power line of the motor without PWM control.
Protect the lines from any stress such as bending. Generally, it must have the cross—sectional area of the AC power cable or more.
Rated output capacity of a power supply module y 30— minute rated output of a spindle motor For the rated output capacities of the power supply modules, see Table 4. If the insulating transformer is installed outside the power magnetics cabinet, and the cable connecting the amplifier is exposed, the cable must be covered with a grounded metal duct, or an AC line filter must be installed.
Some measuring instruments for measuring leakage current may sense a high frequency band, thus showing a larger value. F Tighten all screws firmly.
Fanuc Servo Amplifier Alpha Series Descriptions E pdf – CNC Manual
Preventive measures against noise, including g for external electronic devices affected by noise, must be taken from the viewpoint of an entire system. Never touch them directly. F Notes on cleaning the heat sink and fan 1 A dirty heat sink or fan results in reduced semiconductor cooling efficiency, which degrades reliability.
For combinations of servo motors and servo amplifier modules, see Sections 3.
Take appropriate corrective action, then resume 65162f. Also, keep the specifications at hand. The rated current of the noise filter being used is determined according to the type of the CNC that is connected, the type and number of motors, and the power consumption of the other peripheral devices. F Never touch the regenerative discharge resistor or radiator directly.
Fanuc Servo Amplifier Alpha Series Descriptions 65162E
Select a power supply module with a rated output not less than the sum of the total continuous rated output of the spindle motors times 1. While 61562e LED is lit, hazardous voltages are present inside the unit, and thus there is a danger of electric shock. F Notes on replacing the battery of the absolute pulse coder Replace the battery only while the power is on. The ordering drawing number of the fuses required for each module and the fuse configuration are shown below.
D When the power supply is used in an area where the input voltage is not within the range of to VAC, a power transformer is 6562e. A loose screw, loose connection, or the like will cause a motor malfunction or overheating, or a ground fault.
D The system ground cable must have 6512e cross—sectional area to safely carry the accidental current flow into the system ground when an accident such as a short circuit occurs. F When operating the machine for the first time, check that the machine operates as 6162e.
Fanuc B Manuals User Guides – CNC Manual
Clamping must always be performed since it is very important for stable system operation. A cable to be shielded must be securely connected to the ground plate, using a cable clamp or the 56162e. The module uses power regeneration that returns energy to the power supply during motor deceleration regeneration.
For dimensions, see Sections 8. D The primary power supply and main circuit and the secondary control circuit are separated from each other by reinforced insulation. Regenerative discharge unit This unit is a resistance used to consume energy during motor deceleration regeneration. F Keep the parameter table and spare parts at hand. In this manual we have tried as much as possible to describe all the various matters. The maintenance manual describes daily maintenance and the procedures to be followed in the event of an alarm being issued.
There are two types of servo amplifier module, as follows: The flow of cooling air must not be obstructed. Check that the magnetic contactor, circuit breaker, and other devices mounted outside the amplifier are securely connected to each other and that those devices are securely connected to the amplifier. This section presents a severe risk of electric shock. For the continuous rated outputs of spindle motors, see Table 3. Adequate countermeasures against noise are required to maintain normal operation of the amplifier.
Rotor inertia of motor [kg? In the frame h system, the frames, cases of the units, panels, and shields for the interface cables between the units are connected.